A computational model has been developed to study the mechanisms responsible for hot gas ingestion into the wheel-space cavity of a stationary high pressure turbine (HPT) cascade rig. Simulations were undertaken for the stationary rig described by Bunker et al. (2009, “An Investigation of Turbine Wheelspace Cooling Flow Interactions With a Transonic Hot Gas Path—Part I: Experimental Measurements,” ASME Paper No. GT2009-59237) in a companion paper. The rig consists of five vanes, a wheel-space cavity, and five cylinders that represent the blockage due to the leading edge of the rotor airfoils. The experimental program investigated two cylinder diameters and three clocking positions for a nominal coolant flow rate. Comparisons are made between the computed and measured flow-fields for the smaller of the two cylinders. It is demonstrated that the circumferential variation of pressure established by the vane wake and leading edge bow wave results in an unstable shear layer over the rim seal axial gap (trench) that causes hot gases to ingest for a nominal coolant flow. Steady-state computational fluid dynamics (CFD) simulations did not capture this effect and it was determined that an unsteady analysis was required in order to match the experimental data. Favorable agreement is noted between the time-averaged computed and measured pressure distributions in the circumferential direction both upstream and downstream of the trench, as well as within the trench itself. Furthermore, it is noted that time-averaged buffer cavity effectiveness agrees to within 5% of the experimental data for the cases studied. The validated CFD model is then used to simulate the effect of rotation by rotating the cylinders and disk at rotational rate that scales with a typical engine. A sliding mesh interface is utilized to communicate data between the stator and rotor domains. The stationary cases tend to ingest past the first angel-wing for a nominal coolant flow condition, whereas the effect of rotation helps pressurize the cavity and is responsible for preventing hot gas from entering the buffer cavity.
Skip Nav Destination
Article navigation
October 2011
Research Papers
An Investigation of Turbine Wheelspace Cooling Flow Interactions With a Transonic Hot Gas Path—Part II: CFD Simulations
R. S. Bunker,
R. S. Bunker
General Electric Global Research Center
, Niskayuna, NY 12309
Search for other works by this author on:
J. C. Bailey,
J. C. Bailey
General Electric Global Research Center
, Niskayuna, NY 12309
Search for other works by this author on:
G. Ledezma,
G. Ledezma
General Electric Global Research Center
, Niskayuna, NY 12309
Search for other works by this author on:
S. Kapetanovic,
S. Kapetanovic
General Electric Energy
, Greenville, SC 29615
Search for other works by this author on:
G. M. Itzel,
G. M. Itzel
General Electric Energy
, Greenville, SC 29615
Search for other works by this author on:
M. A. Sullivan,
M. A. Sullivan
General Electric Energy
, Greenville, SC 29615
Search for other works by this author on:
T. R. Farrell
T. R. Farrell
General Electric Energy
, Greenville, SC 29615
Search for other works by this author on:
G. M. Laskowski
R. S. Bunker
General Electric Global Research Center
, Niskayuna, NY 12309
J. C. Bailey
General Electric Global Research Center
, Niskayuna, NY 12309
G. Ledezma
General Electric Global Research Center
, Niskayuna, NY 12309
S. Kapetanovic
General Electric Energy
, Greenville, SC 29615
G. M. Itzel
General Electric Energy
, Greenville, SC 29615
M. A. Sullivan
General Electric Energy
, Greenville, SC 29615
T. R. Farrell
General Electric Energy
, Greenville, SC 29615J. Turbomach. Oct 2011, 133(4): 041020 (12 pages)
Published Online: April 25, 2011
Article history
Received:
August 11, 2009
Revised:
November 21, 2009
Online:
April 25, 2011
Published:
April 25, 2011
Citation
Laskowski, G. M., Bunker, R. S., Bailey, J. C., Ledezma, G., Kapetanovic, S., Itzel, G. M., Sullivan, M. A., and Farrell, T. R. (April 25, 2011). "An Investigation of Turbine Wheelspace Cooling Flow Interactions With a Transonic Hot Gas Path—Part II: CFD Simulations." ASME. J. Turbomach. October 2011; 133(4): 041020. https://doi.org/10.1115/1.4002410
Download citation file:
Get Email Alerts
The Cooling Effect of Combustor Exit Louver Scheme on a Transonic Nozzle Guide Vane Endwall
J. Turbomach (July 2025)
Aerodynamic Performance Evaluation of Subsonic Compressor Cascade Blade With Leading-Edge Damage
J. Turbomach (July 2025)
Thermohydraulic Performance and Flow Structures of Diamond Pyramid Arrays
J. Turbomach (July 2025)
Related Articles
Film-Cooling Effectiveness on a Rotating Turbine Platform Using Pressure Sensitive Paint Technique
J. Turbomach (October,2010)
An Investigation of Turbine Wheelspace Cooling Flow Interactions With a Transonic Hot Gas Path—Part 1: Experimental Measurements
J. Turbomach (April,2011)
Interaction of Wheelspace Coolant and Main Flow in a New Aeroderivative Low Pressure Turbine
J. Turbomach (July,2010)
Aerothermal Impact of Stator-Rim Purge Flow and Rotor-Platform Film Cooling on a Transonic Turbine Stage
J. Turbomach (April,2010)
Related Proceedings Papers
Related Chapters
Control and Operational Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Thermodynamic Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Outlook
Closed-Cycle Gas Turbines: Operating Experience and Future Potential