A comprehensive method of thermo-elastohydrodynamic lubrication analysis for connecting rod bearings is proposed, which includes thermal distortion as well as elastic deformation of the bearing surface. Lubrication film temperature is treated as a time-dependent, two-dimensional variable which is averaged over the film thickness, while the bearing temperature is assumed to be time-independent and three-dimensional. It is assumed that a portion of the heat generated by viscous dissipation in the lubrication film is absorbed by the film itself, and the remainder flows into the bearing structure. Mass-conserving cavitation algorithm is applied, and the effect of variable viscosity is included in the Reynolds equation. Simulation results of the connecting rod bearing of an internal combustion engine are presented. It is shown that the predicted level of the thermal distortion is as large as that of the elastic deformation and the bearing clearance, and that the thermal distortion has remarkable effects on the bearing performance. Therefore, the thermo-elastohydrodynamic lubrication analysis is strongly recommended to predict the performance of connecting rod bearings in internal combustion engines.

Issue Section:
Technical Papers
Keywords:
simulation, thermoelasticity, machine bearings, internal combustion engines, cavitation, lubrication, elastic deformation
Topics:
Bearings, Lubrication, Cavitation
1.
Xu
,
H.
,
1999
, “
Recent Advances in Engine Bearing Design Analysis
,”
Proc. Inst. Mech. Eng.
, Part J,
213
, pp.
51
–
74
.
2.
Fantino
,
B.
, and
Frene
,
J.
,
1985
, “
Comparison of Dynamic Behavior of Elastic Connecting-Rod Bearing in Both Petrol and Diesel Engines
,”
ASME J. Tribol.
,
107
, pp.
87
–
91
.
3.
Oh
,
K. P.
,
1984
, “
The Numerical Solution of Dynamically Loaded Elastohydrodynamic Contact as a Nonlinear Complementarity Problem
,”
ASME J. Tribol.
,
106
, pp.
88
–
95
.
4.
Oh
,
K. P.
, and
Goenka
,
P. K.
,
1985
, “
The Elastohydrodynamic Solution of Journal Bearings Under Dynamic Loading
,”
ASME J. Tribol.
,
107
, pp.
389
–
395
.
5.
Van der Tempel
,
L.
,
Moes
,
H.
, and
Bosma
,
R.
,
1985
, “
Starvation in Dynamically Loaded Flexible Short Journal Bearings
,”
ASME J. Tribol.
,
107
, pp.
516
–
521
.
6.
Bonneau
,
D.
,
Guines
,
D.
,
Frene
,
J.
, and
Toplosky
,
J.
,
1995
, “
EHD Analysis, Including Structural Inertia Effects and A Mass-Conserving Cavitation Model
,”
ASME J. Tribol.
,
117
, pp.
540
–
547
.
7.
Boedo
,
S.
, and
Booker
,
J. F.
,
1997
, “
Surface Roughness and Structural Inertia in a Mode-Based Mass-Conserving Elastohydrodynamic Lubrication Model
,”
ASME J. Tribol.
,
119
, pp.
449
–
455
.
8.
Kumar
,
A.
, and
Booker
,
J. F.
,
1991
, “
A Finite Element Cavitation Algorithm
,”
ASME J. Tribol.
,
113
, pp.
276
–
286
.
9.
Kumar
,
A.
, and
Booker
,
J. F.
,
1991
, “
A Finite Element Cavitation Algorithm: Application/Validation
,”
ASME J. Tribol.
,
113
, pp.
255
–
261
.
10.
Kumar
,
A.
,
Goenka
,
P. K.
, and
Booker
,
J. F.
,
1990
, “
Modal Analysis of Elastohydrodynamic Lubrication: A Connecting Rod Application
,”
ASME J. Tribol.
,
112
, pp.
524
–
534
.
11.
Smith, E. H., 1983, “Temperature Variations in Crankshaft Bearings,” Proceedings of the 9th Leeds-Lyon Symposium on Tribology, September 1982, pp. 49–54.
12.
Paranjpe
,
R. S.
, and
Han
,
T.
,
1995
, “
A Transient Thermohydrodynamic Analysis Including Mass Conserving Cavitation for Dynamically Loaded Journal Bearings
,”
ASME J. Tribol.
,
117
, pp.
369
–
378
.
13.
Zhang, C., Jiang, J. X., and Cheng, H. S., 1999, “A Transient Thermohydrodynamic Analysis of Dynamically Loaded Finite Journal Bearings with Rough Surface Including Mass Conserving Cavitation,” Proceedings of the 25th Leeds-Lyon Symposium on Tribology, September 1998, pp. 367–378.
14.
Cho
,
M.-R.
,
Han
,
D.-C.
, and
Choi
,
J.-K.
,
1999
, “
Oil Film Thickness in Engine Connecting-Rod Bearing With Consideration of Thermal Effects: Comparison Between Theory and Experiment
,”
ASME J. Tribol.
,
121
, pp.
901
–
907
.
15.
Moes
,
H.
,
Ten Hoeve
,
P. B. Y.
, and
Van der Helm
,
J.
,
1989
, “
Thermal Effects in Dynamically Loaded Flexible Journal Bearing
,”
ASME J. Tribol.
,
111
, pp.
49
–
55
.
16.
Piffeteau
,
S.
,
Souchet
,
D.
, and
Bonneau
,
D.
,
2000
, “
Influence of Thermal and Elastic Deformations on Connecting-Rod Big End Bearing Lubrication Under Dynamic Loading
,”
ASME J. Tribol.
,
122
, pp.
181
–
191
.
17.
Booker
,
J. F.
,
1971
, “
Dynamically-Loaded Journal Bearings: Numerical Application of the Mobility Method
,”
ASME J. Lubr. Technol.
,
93
, pp.
168
–
176
(Errata: p. 315).
18.
Rohde, S. M., 1978, “Thick Film and Transient Elastohydrodynamic Lubrication Problems,” Fundamentals of Tribology, Suh, N. P. and Saka, N., Eds., MIT Press, pp. 1075–1101.
19.
Pozrikidis, C., 1997, Introduction to Theoretical and Computational Fluid Dynamics, Oxford University Press, New York.
20.
McIvor
,
J. D. C.
, and
Fenner
,
D. N.
,
1989
, “
Finite Element Analysis of Dynamically Loaded Flexible Journal Bearings: A Fast Newton-Raphson Method
,”
ASME J. Tribol.
,
111
, pp.
597
–
604
.
21.
Campbell
,
J.
,
Love
,
P. P.
,
Martin
,
F. A.
, and
Rafique
,
S. O.
,
1967
–68, “
Bearings for Reciprocating Machinery: A Review of the Present State of Theoretical, Experimental and Service Knowledge
,”
Proc. Inst. Mech. Eng.
,
182
, pp.
51
–
74
.
22.
Xu
,
H.
, and
Smith
,
E. H.
,
1990
, “
A New Approach to the Solution of Elastohydrodynamic Lubrication of Crankshaft Bearings
,”
Proc. Inst. Mech. Eng., Part C
,
204
, pp.
187
–
197
.
Copyright © 2001
 by ASME
You do not currently have access to this content.