Volume 129 Issue 2 | J. Pressure Vessel Technol.

Skip Nav Destination

Editorial

Special Issue of the JPVT From the Design and Analysis Committee

Dennis K. Williams

J. Pressure Vessel Technol. May 2007, 129(2): 225. doi: https://doi.org/10.1115/1.2722298

Extract

View articletitled, Special Issue of the JPVT From the Design and Analysis Committee

Open the PDF for in another window

Topics: Design , Pipes , Pressure vessels

Research Papers

Dynamic Pipe Stresses During Water Hammer: A Finite Element Approach

Robert A. Leishear

J. Pressure Vessel Technol. May 2007, 129(2): 226–233. doi: https://doi.org/10.1115/1.2716420

Abstract

View articletitled, Dynamic Pipe Stresses During Water Hammer: A Finite Element Approach

Open the PDF for in another window

Topics: Finite element analysis , Pipes , Stress , Pressure , Water hammer , Waves

Comparison of Residual Stresses in the Mechanical Roll Expansion of HX Tubes Into TEMA Grooves

Dennis K. Williams

J. Pressure Vessel Technol. May 2007, 129(2): 234–241. doi: https://doi.org/10.1115/1.2716426

Abstract

View articletitled, Comparison of Residual Stresses in the Mechanical Roll Expansion of HX Tubes Into TEMA Grooves

Open the PDF for in another window

Topics: Finite element analysis , Heat exchangers , Residual stresses , Stainless steel , Stress

Improving the Reliability of the Tube-Hydroforming Process by the Taguchi Method

Bing Li, T. J. Nye, Don R. Metzger

J. Pressure Vessel Technol. May 2007, 129(2): 242–247. doi: https://doi.org/10.1115/1.2716427

Abstract

View articletitled, Improving the Reliability of the Tube-Hydroforming Process by the Taguchi Method

Open the PDF for in another window

Topics: Design , Finite element analysis , Reliability , Simulation , Taguchi methods

Slip Blinds at Pressures Causing Permanent Deformation

Jaan Taagepera, Trevor G. Seipp

J. Pressure Vessel Technol. May 2007, 129(2): 248–253. doi: https://doi.org/10.1115/1.2716428

Abstract

View articletitled, Slip Blinds at Pressures Causing Permanent Deformation

Open the PDF for in another window

Topics: Deformation , Finite element analysis , Flanges , Pipes , Pressure , Deflection , Testing

Modeling of the Behavior of a Welded Joint Subjected to Reverse Bending Moment at High Temperature

Alan R. S. Ponter, Haofeng Chen

J. Pressure Vessel Technol. May 2007, 129(2): 254–261. doi: https://doi.org/10.1115/1.2716429

Abstract

View articletitled, Modeling of the Behavior of a Welded Joint Subjected to Reverse Bending Moment at High Temperature

Open the PDF for in another window

Topics: Creep , Failure , Fatigue , Stress , Welded joints , Modeling , Plasticity , Damage , High temperature , Cycles

Steady-State Thermal Simulation of Weld Applied to a Practical Axisymmetric Weldment

Ken Uchida, Rie Sumiya, Tadashi Murofushi, Masakazu Jimbo

J. Pressure Vessel Technol. May 2007, 129(2): 262–271. doi: https://doi.org/10.1115/1.2716430

Abstract

View articletitled, Steady-State Thermal Simulation of Weld Applied to a Practical Axisymmetric Weldment

Open the PDF for in another window

Topics: Computational fluid dynamics , Heat , Simulation , Steady state , Temperature , Welded joints , Thermal analysis

Failure of Locally Buckled Pipelines

E. Dama, S. A. Karamanos, A. M. Gresnigt

J. Pressure Vessel Technol. May 2007, 129(2): 272–279. doi: https://doi.org/10.1115/1.2716431

Abstract

View articletitled, Failure of Locally Buckled Pipelines

Open the PDF for in another window

Topics: Cycles , Failure , Finite element analysis , Pipelines , Pipes , Pressure , Simulation , Steel , Stress , Fatigue

Limit Loads of Pressure Components Using the Reference Two-Bar Structure

R. Seshadri, R. Adibi-Asl

J. Pressure Vessel Technol. May 2007, 129(2): 280–286. doi: https://doi.org/10.1115/1.2716432

Abstract

View articletitled, Limit Loads of Pressure Components Using the Reference Two-Bar Structure

Open the PDF for in another window

Topics: Pressure , Stress

Shakedown Limits of a $90 - Degree$ Pipe Bend Using Small and Large Displacement Formulations

Hany F. Abdalla, Mohammad M. Megahed, Maher Y. A. Younan

J. Pressure Vessel Technol. May 2007, 129(2): 287–295. doi: https://doi.org/10.1115/1.2716433

Abstract

View articletitled, Shakedown Limits of a <math xmlns="http://www.w3.org/1998/Math/MathML"><mrow xmlns=""><mn>90</mn><mtext>-</mtext><mi>Degree</mi></mrow></math> Pipe Bend Using Small and Large Displacement Formulations

Open the PDF for in another window

Topics: Displacement , Pipe bends , Stress , Pressure

Local Limit-Load Analysis Using the $m_{β}$ Method

R. Adibi-Asl, R. Seshadri

J. Pressure Vessel Technol. May 2007, 129(2): 296–305. doi: https://doi.org/10.1115/1.2716434

Abstract

View articletitled, Local Limit-Load Analysis Using the <math xmlns="http://www.w3.org/1998/Math/MathML"><msub xmlns=""><mi>m</mi><mi>β</mi></msub></math> Method

Open the PDF for in another window

Topics: Elastic moduli , Stress , Finite element analysis , Fracture (Materials)

Mode-I Stress-Intensity Factors for a Cracked Slab Under an Arbitrary Thermal Shock

A. E. Segall, J. Meeker

J. Pressure Vessel Technol. May 2007, 129(2): 306–312. doi: https://doi.org/10.1115/1.2716435

Abstract

View articletitled, Mode-I Stress-Intensity Factors for a Cracked Slab Under an Arbitrary Thermal Shock

Open the PDF for in another window

Topics: Polynomials , Slabs , Stress , Thermal shock , Transients (Dynamics) , Fracture (Materials) , Thermoelasticity

High-Temperature Heat Exchanger Tube-Sheet Assembly Investigation With Computational Fluid Dynamics

Michael A. Porter, Dennis H. Martens, Thomas Duffy, Sean McGuffie

J. Pressure Vessel Technol. May 2007, 129(2): 313–315. doi: https://doi.org/10.1115/1.2716436

Abstract

View articletitled, High-Temperature Heat Exchanger Tube-Sheet Assembly Investigation With Computational Fluid Dynamics

Open the PDF for in another window

Topics: Computational fluid dynamics , High temperature , Manufacturing , Temperature , Carbon steel , Heat exchangers , Flow (Dynamics) , Heat transfer , Temperature distribution

Considerations in the Design and Analysis of an ASME Section VIII, Div. 2 Reactor Support Skirt

Dennis K. Williams, Trevor G. Seipp

J. Pressure Vessel Technol. May 2007, 129(2): 316–322. doi: https://doi.org/10.1115/1.2722301

Abstract

View articletitled, Considerations in the Design and Analysis of an ASME Section VIII, Div. 2 Reactor Support Skirt

Open the PDF for in another window

Topics: Boundary-value problems , Design , Finite element analysis , Fourier series , Stress , Temperature , Friction , Shells , Vessels , Heat transfer

Technical Brief

Note on Shear Load-Testing Feedwater Heater Tube Joints

Stanley Yokell

J. Pressure Vessel Technol. May 2007, 129(2): 323–325. doi: https://doi.org/10.1115/1.2716437

Abstract

View articletitled, Note on Shear Load-Testing Feedwater Heater Tube Joints

Open the PDF for in another window

Topics: Feedwater , Shear (Mechanics) , Stress , Testing , Welded joints , Welding , Deformation , Tensile strength , Tubular joints , Metals

Design Innovation Papers

Proposed Design Criterion for Vessel Lifting Lugs in Lieu of ASME B30.20

Dennis K. Williams

J. Pressure Vessel Technol. May 2007, 129(2): 326–333. doi: https://doi.org/10.1115/1.2716439

Abstract

View articletitled, Proposed Design Criterion for Vessel Lifting Lugs in Lieu of ASME B30.20

Open the PDF for in another window

Topics: Design , Stress , Vessels , Regulations , Pressure vessels , Failure , Safety , Safety engineering

Design for Leakage in Flange Joints Under External Loads

William J. Koves

J. Pressure Vessel Technol. May 2007, 129(2): 334–337. doi: https://doi.org/10.1115/1.2716700

Abstract

View articletitled, Design for Leakage in Flange Joints Under External Loads

Open the PDF for in another window

Topics: Flanges , Gaskets , Leakage , Stress , Design , Pressure , Pressure vessels

Determining Effective Thickness of Cylinders in Pressure Equipment With Significant Thickness Variations for Fitness for Service Assessments

Clay D. Rodery

J. Pressure Vessel Technol. May 2007, 129(2): 338–341. doi: https://doi.org/10.1115/1.2716440

Abstract

View articletitled, Determining Effective Thickness of Cylinders in Pressure Equipment With Significant Thickness Variations for Fitness for Service Assessments

Open the PDF for in another window

Topics: Corrosion , Cylinders , Fitness-for-service , Maintenance , Pressure equipment , Erosion , Vessels

Erratum

Erratum: “Incorporating Neural Network Material Models Within Finite Element Analysis for Rheological Behavior Prediction” [Journal of Pressure Vessel Technology, 2007, 129(1), pp. 58–65]

B. Scott Kessler, A. Sherif El-Gizawy, Douglas E. Smith

J. Pressure Vessel Technol. May 2007, 129(2): 342. doi: https://doi.org/10.1115/1.2728894

Extract

View articletitled, Erratum: “Incorporating Neural Network Material Models Within Finite Element Analysis for Rheological Behavior Prediction” [Journal of Pressure Vessel Technology, 2007, 129(1), pp. 58–65]

Open the PDF for in another window

Topics: Artificial neural networks , Finite element analysis , Pressure vessels , Rheology

Editorial

Special Issue of the JPVT From the Design and Analysis Committee

Research Papers

Dynamic Pipe Stresses During Water Hammer: A Finite Element Approach

Comparison of Residual Stresses in the Mechanical Roll Expansion of HX Tubes Into TEMA Grooves

Improving the Reliability of the Tube-Hydroforming Process by the Taguchi Method

Slip Blinds at Pressures Causing Permanent Deformation

Modeling of the Behavior of a Welded Joint Subjected to Reverse Bending Moment at High Temperature

Steady-State Thermal Simulation of Weld Applied to a Practical Axisymmetric Weldment

Failure of Locally Buckled Pipelines

Limit Loads of Pressure Components Using the Reference Two-Bar Structure

Shakedown Limits of a $90 - Degree$ Pipe Bend Using Small and Large Displacement Formulations

Local Limit-Load Analysis Using the $m_{β}$ Method

Mode-I Stress-Intensity Factors for a Cracked Slab Under an Arbitrary Thermal Shock

High-Temperature Heat Exchanger Tube-Sheet Assembly Investigation With Computational Fluid Dynamics

Considerations in the Design and Analysis of an ASME Section VIII, Div. 2 Reactor Support Skirt

Technical Brief

Note on Shear Load-Testing Feedwater Heater Tube Joints

Design Innovation Papers

Proposed Design Criterion for Vessel Lifting Lugs in Lieu of ASME B30.20

Design for Leakage in Flange Joints Under External Loads

Determining Effective Thickness of Cylinders in Pressure Equipment With Significant Thickness Variations for Fitness for Service Assessments

Erratum

Erratum: “Incorporating Neural Network Material Models Within Finite Element Analysis for Rheological Behavior Prediction” [Journal of Pressure Vessel Technology, 2007, 129(1), pp. 58–65]

Email alerts

RSS Feeds

ASME Journals

ASME Conference Proceedings

ASME eBooks

Resources

Opportunities

Issues

Editorial

Research Papers

Technical Brief

Design Innovation Papers

Erratum

Email alerts

RSS Feeds

ASME Journals

ASME Conference Proceedings

ASME eBooks

Resources

Opportunities

This Feature Is Available To Subscribers Only