Cold-rolled steel sheets of thicknesses ranging from 0.5 to 1.0 mm were used to produce tailor-welded blanks (TWBs) with various thickness ratios. In this study, the formability of the TWBs, as well as the mechanical characteristics of the weld zones, were analyzed experimentally under the effects of various thickness ratios of TWBs. The formability of the TWBs was evaluated in terms of three measures—failure mode, forming limit diagram, and minimum major strain, whereas the mechanical characteristics of the weld zones were investigated by tensile testing, metallographic study, and microhardness measurement. In particular, circular TWBs with different radii and cutoff widths were designed where all the welds were located in the center of the blanks and perpendicular to the principal strain direction. Nd:YAG laser butt-welding was used to weld the TWB specimens of different thickness ratios. The experimental findings in this study showed that the higher the thickness ratio of the TWBs, the lower the forming limit curve level, and the lower formability. The minimum major strain was clearly inversely proportional to the thickness ratio of the TWBs. On the other hand, the results of uniaxial tensile tests clearly illustrated that there was no significant difference between the tensile strengths of the TWBs and those of the base metals. The metallographic study demonstrated a difference of grain size in the materials at base metal, heat-affected zones, and fusion zone. The microhardness measurement indicated that the hardness in the fusion zone increased by about 60% of the base metal.
Skip Nav Destination
e-mail: mflcchan@inet.polyu.edu.hk
Article navigation
April 2005
Article
Formability and Weld Zone Analysis of Tailor-Welded Blanks for Various Thickness Ratios
L. C. Chan,
e-mail: mflcchan@inet.polyu.edu.hk
L. C. Chan
Department of Industrial and Systems Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong, China
Search for other works by this author on:
S. M. Chan,
S. M. Chan
Department of Industrial and Systems Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong, China
Search for other works by this author on:
C. H. Cheng,
C. H. Cheng
Department of Industrial and Systems Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong, China
Search for other works by this author on:
T. C. Lee
T. C. Lee
Department of Industrial and Systems Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong, China
Search for other works by this author on:
L. C. Chan
Department of Industrial and Systems Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong, China
e-mail: mflcchan@inet.polyu.edu.hk
S. M. Chan
Department of Industrial and Systems Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong, China
C. H. Cheng
Department of Industrial and Systems Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong, China
T. C. Lee
Department of Industrial and Systems Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong, China
Manuscript received January 15, 2004; revision received October 15, 2004. Review conducted by: M. F. Horstemeyer.
J. Eng. Mater. Technol. Apr 2005, 127(2): 179-185 (7 pages)
Published Online: April 6, 2005
Article history
Received:
January 15, 2004
Revised:
October 15, 2004
Online:
April 6, 2005
Citation
Chan, L. C., Chan , S. M., Cheng , C. H., and Lee, T. C. (April 6, 2005). "Formability and Weld Zone Analysis of Tailor-Welded Blanks for Various Thickness Ratios ." ASME. J. Eng. Mater. Technol. April 2005; 127(2): 179–185. https://doi.org/10.1115/1.1857936
Download citation file:
Get Email Alerts
Modeling Growth and Viscous Flow of Oxide on Cylindrical Silicon Surfaces Including Piezoviscous Inhibition
J. Eng. Mater. Technol (April 2025)
Thermal Conductivity of 3D-Printed Metal Using Extrusion-Based Metal Additive Manufacturing Process
J. Eng. Mater. Technol (April 2025)
Related Articles
Numerical Simulations and Experimental Results of Tensile Test Behavior of Laser Butt Welded DP980 Steels
J. Eng. Mater. Technol (October,2008)
A Comparative Study of Formability of Diode Laser Welds in DP980 and HSLA Steels
J. Eng. Mater. Technol (July,2007)
Formability Analysis of Tailor-Welded Blanks of Different Thickness Ratios
J. Manuf. Sci. Eng (November,2005)
Interfacial Structure and Micro and Nano-Mechanical Behavior of Laser-Welded 6061 Aluminum Alloy Blank
J. Eng. Mater. Technol (January,2004)
Related Proceedings Papers
Related Chapters
Final Report
Applications Guide for Determining the Yield Strength of In-Service Pipe by Hardness Evaluation: Final Report
The Necessary Fine-Tuning of Process Management and Controls for Metallic Transformations during Manufacturing of Bearings: Application to M50NiL Steel
Bearing and Transmission Steels Technology
Historical Overview
History of Line Pipe Manufacturing in North America