Stress corrosion cracking of Type 304 stainless steel has been studied with fracture-mechanics-type standard 25.4-mm-thick compact tension specimens in simulated boiling-water reactor environments at 289°C and 8.3 MPa. Tests were performed with either constant or cyclic loading. The latter tests used a positive sawtooth waveform with an unloading time of 1 or 5 s, a load ratio R (minimum load to maximum load) of 0.2 to 0.95, and a frequency f of 8 × 10−4 to 1 × 10−1 Hz. Crack lengths and crack growth rates were determined by the compliance method; crack mouth opening displacement was measured with in-situ clip gauges. Fractography was used to examine the mode of cracking and to confirm the compliance method for crack length determination. The test environments were high-purity deionized water with 0.2- to 8-ppm dissolved oxygen, and water with 0.2-ppm dissolved oxygen and 0.1-ppm sulfate (as H2SO4). Two heats with a carbon content of 0.06 wt percent were investigated in solution-heat-treated and furnace-sensitized conditions. Degree of sensitization varied from ∼0 to 20 C/cm2 as measured by the electrochemical potentiokinetic polarization method. The first heat was tested in water with 0.2- and 8-ppm dissolved oxygen and with 0.2-ppm dissolved oxygen and 0.1-ppm sulfate. The loading conditions encompassed the range f=8×10−2 to 8 × 10−4 Hz, Kmax=28 to 72 MPa•m1/2, and R = 0.95. Under these conditions, the crack growth rates were ∼0 to 3 × 10−9 m/s. The effects of water chemistry transients which produced changes in the concentration of dissolved oxygen or sulfate in the environment were also investigated. The second heat was tested in water with 8-ppm dissolved oxygen. The influence of load ratio and frequency was investigated over the range R = 0.5 to 1.0 and f = 1 × 10−1 to 2 × 10−3 Hz, at maximum stress intensity Kmax = 28 to 38 MPa•m1/2. Under these conditions, crack growth rates varied from 1 × 10−10 to 3 × 10−9 m/s. Crack growth rate increased significantly at low R values. However, the growth rate at R = 0.95 was not significantly different from that under constant load. Correlation of the crack growth rate data with crack-tip strain rates is discussed.
Skip Nav Destination
Article navigation
January 1986
Research Papers
Stress Corrosion Crack Growth Rates in Type 304 Stainless Steel in Simulated BWR Environments
J. Y. Park,
J. Y. Park
Materials Science and Technology Division, Argonne National Laboratory, Argonne, Ill. 60439
Search for other works by this author on:
W. E. Ruther,
W. E. Ruther
Materials Science and Technology Division, Argonne National Laboratory, Argonne, Ill. 60439
Search for other works by this author on:
T. F. Kassner,
T. F. Kassner
Materials Science and Technology Division, Argonne National Laboratory, Argonne, Ill. 60439
Search for other works by this author on:
W. J. Shack
W. J. Shack
Materials Science and Technology Division, Argonne National Laboratory, Argonne, Ill. 60439
Search for other works by this author on:
J. Y. Park
Materials Science and Technology Division, Argonne National Laboratory, Argonne, Ill. 60439
W. E. Ruther
Materials Science and Technology Division, Argonne National Laboratory, Argonne, Ill. 60439
T. F. Kassner
Materials Science and Technology Division, Argonne National Laboratory, Argonne, Ill. 60439
W. J. Shack
Materials Science and Technology Division, Argonne National Laboratory, Argonne, Ill. 60439
J. Eng. Mater. Technol. Jan 1986, 108(1): 20-25 (6 pages)
Published Online: January 1, 1986
Article history
Received:
August 1, 1985
Online:
September 23, 2009
Citation
Park, J. Y., Ruther, W. E., Kassner, T. F., and Shack, W. J. (January 1, 1986). "Stress Corrosion Crack Growth Rates in Type 304 Stainless Steel in Simulated BWR Environments." ASME. J. Eng. Mater. Technol. January 1986; 108(1): 20–25. https://doi.org/10.1115/1.3225835
Download citation file:
Get Email Alerts
Cited By
Investigating Microstructure and Wear Characteristics of Alloy Steels Used as Wear Plates in Ballast Cleaning Operation in Railways
J. Eng. Mater. Technol (January 2025)
Related Articles
The Benefit of Hydrogen Addition to the Boiling Water Reactor Environment on Stress Corrosion Crack Initiation and Growth in Type 304 Stainless Steel
J. Eng. Mater. Technol (January,1986)
The Effect of BWR Startup Environments on Crack Growth in Structural Alloys
J. Eng. Mater. Technol (January,1986)
Effect of Oxidation Chemistry of Supercritical Water on Stress Corrosion Cracking of Austenitic Steels
ASME J of Nuclear Rad Sci (January,2016)
Prediction of Materials Damage History From Stress Corrosion Cracking in Boiling Water Reactors
J. Pressure Vessel Technol (February,2000)
Related Proceedings Papers
Related Chapters
Mathematical Background
Vibrations of Linear Piezostructures
Development of Nuclear Boiler and Pressure Vessels in Taiwan
Companion Guide to the ASME Boiler and Pressure Vessel Code, Volume 3, Third Edition
Effects of Metallic Plate and Objects on Performance of Inverted F Antenna for ISM Band Application
International Conference on Computer and Automation Engineering, 4th (ICCAE 2012)