In this paper, the contribution of tool wear to friction was determined for precision hard turning using Cubic Borone Nitride (CBN) cutting tools. The tool nose wear VBC and the corresponding changes of component forces Fc, Ff, and Fp resulting from tool wear evolution were continuously measured during wear tests. Based on the mechanics of nonorthogonal cutting, the normal and friction forces acting on rake and flank faces were calculated for all measuring points, and as a result, relevant changes of the friction coefficient were determined. Additionally, friction changes resulting from tool wear under different feed rate, depth of cut, and tool nose radius were discussed in terms of the plowing energy produced by the tool nose.
Issue Section:
Research Papers
References
1.
Davim
, J. P.
, 2011
, Machining of Hard Materials
, Springer
, London
.2.
Byrne
, G.
, Dornfeld
, D.
, and Denkena
, D.
, 2003
, “Advancing Cutting Technology
,” CIRP Ann.
, 52
(2
), pp. 483
–507
.3.
Grzesik
, W.
, and Żak
, K.
, 2015
, “Possibilities of the Generation of Hardened Steel Parts With Defined Topographic Characteristics of the Machined Surfaces
,” ASME J. Manuf. Sci. Eng.
, 137
(1
), p. 014502
.4.
Ninggang
, S.
, and Hongtao
, D.
, 2014
, “Physics-Based Microstructure Simulation for Drilled Hole Surface in Hardened Steel
,” ASME J. Manuf. Sci. Eng.
, 136
(4
), p. 044504
.5.
Tönshoff
, H. K.
, Arendt
, C.
, and Ben Amor
, R.
, 2000
, “Cutting of Hardened Steel
,” CIRP Ann.
, 49
(2
), pp. 547
–566
.6.
Davies
, M. A.
, Chou
, Y.
, and Evans
, C. J.
, 1996
, “On Chip Morphology, Tool Wear and Cutting Mechanics
,” CIRP Ann.
, 45
(1
), pp. 77
–82
.7.
Hongtao
, D.
, and Yung
, C. S.
, 2014
, “Dislocation Density-Based Grain Refinement Modeling of Orthogonal Cutting of Titanium
,” ASME J. Manuf. Sci. Eng.
, 136
(4
), p. 041003
.8.
Özel
, T.
, Karpat
, Y.
, and Srivastawa
, A.
, 2009
, “Hard Turning With Variable Micro-Geometry PcBN Tools
,” CIRP Ann.-Manuf. Technol.
, 57
(1
), pp. 73
–76
.9.
Pandit
, S. M.
, and Kashou
, S.
, 1983
, “Variation in Friction Coefficient With Tool Wear
,” Wear
, 84
(1
), pp. 65
–79
.10.
Mayer
, R.
, Köhler
, J.
, and Denkena
, B.
, 2012
, “Influence of the Tool Corner Radius on the Tool Wear and Process Forces During Hard Turning
,” Int. J. Adv. Manuf. Technol.
, 58
(9–12
), pp. 933
–940
.11.
Zhou
, J. M.
, Walter
, H.
, Andersson
, M.
, and Stahl
, J. E.
, 2003
, “Effect of Chamfer Angle on Wear of PCBN Cutting Tool
,” Int. J. Mach. Tools Manuf.
, 43
(3
), pp. 301
–305
.12.
Chou
, Y. K.
, and Song
, H.
, 2014
, “Tool Nose Radius Effect on Finish Hard Turning
,” J. Mater. Process. Technol.
, 148
(2
), pp. 259
–268
.13.
Grzesik
, W.
, and Żak
, K.
, 2013
, “Friction Quantification in the Oblique Cutting With CBN Chamfered Tools
,” Wear
, 304
(1–2
), pp. 36
–42
.14.
Hosseini
, S. B.
, Beno
, T.
, Klement
, U.
, Kaminski
, J.
, and Ryttberg
, K.
, 2014
, “Cutting Temperatures During Hard Turning-Measurements and Effects on White Layer Formation in AISI 52100
,” J. Mater. Process. Technol.
, 214
(6
), pp. 1293
–1300
.15.
Rymuza
, Z.
, 1996
, “Energy Concept of the Coefficient of Friction
,” Wear
, 199
(2
), pp. 187
–196
.16.
Boothroyd
, G.
, and Knight
, W. A.
, 2005
, Fundamentals of Machining and Machine Tools
, Taylor & Francis
, New York
.Copyright © 2016 by ASME
You do not currently have access to this content.
