Mixed convection heat transfer characteristics from heat source located symmetrically inside square enclosure and cooled by Al2O3/water-based nanofluid flow was experimentally investigated. The configuration was subjected to high levels of natural convection and low rates of nanofluid flow. The nanofluid thermophysical properties were characterized using the available correlations in the literatures except the viscosity which was measured and correlated in terms of the nanoparticles loading ratios. Comparative analysis indicated that the application of nanofluid could not guarantee heat transfer enhancement in configurations dominated by natural convection. Exception heat transfer enhancement was only found when very low nanoparticles loading ratio was applied. Instead, heat transfer degradation was found especially in the cases of highest nanoparticles loading ratios. Alternatively, heat transfer enhancement was observed when the forced convection effect was substantial at the highest nanofluid flow rate. The present conclusions were justified and correlated to the findings reported in the literature.
Skip Nav Destination
Article navigation
Research-Article
Experimental Heat Transfer From Heating Source Subjected to Rigorous Natural Convection Inside Enclosure and Cooled by Forced Nanofluid Flow
Khaled Khodary Esmaeil,
Khaled Khodary Esmaeil
Mechanical Power Engineering Department,
Faculty of Engineering,
Tanta University,
Tanta 31527, Egypt;
Faculty of Engineering,
Tanta University,
Tanta 31527, Egypt;
Mechanical Engineering Department,
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia
1Corresponding author.
Search for other works by this author on:
Gamal I. Sultan,
Gamal I. Sultan
Mechanical Engineering Department,
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia;
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia;
Mechanical Power Engineering Department,
Faculty of Engineering,
Mansoura University,
Mansoura 35516, Egypt
Faculty of Engineering,
Mansoura University,
Mansoura 35516, Egypt
Search for other works by this author on:
Fahad A. Al-Mufadi,
Fahad A. Al-Mufadi
Mechanical Engineering Department,
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia
Search for other works by this author on:
Radwan A. Almasri
Radwan A. Almasri
Mechanical Engineering Department,
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia
Search for other works by this author on:
Khaled Khodary Esmaeil
Mechanical Power Engineering Department,
Faculty of Engineering,
Tanta University,
Tanta 31527, Egypt;
Faculty of Engineering,
Tanta University,
Tanta 31527, Egypt;
Mechanical Engineering Department,
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia
Gamal I. Sultan
Mechanical Engineering Department,
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia;
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia;
Mechanical Power Engineering Department,
Faculty of Engineering,
Mansoura University,
Mansoura 35516, Egypt
Faculty of Engineering,
Mansoura University,
Mansoura 35516, Egypt
Fahad A. Al-Mufadi
Mechanical Engineering Department,
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia
Radwan A. Almasri
Mechanical Engineering Department,
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia
College of Engineering,
Qassim University,
Buraidah 51452, Saudi Arabia
1Corresponding author.
Contributed by the Heat Transfer Division of ASME for publication in the JOURNAL OF HEAT TRANSFER. Manuscript received March 3, 2018; final manuscript received April 24, 2019; published online May 20, 2019. Assoc. Editor: Antonio Barletta.
J. Heat Transfer. Jul 2019, 141(7): 072501 (9 pages)
Published Online: May 20, 2019
Article history
Received:
March 3, 2018
Revised:
April 24, 2019
Citation
Esmaeil, K. K., Sultan, G. I., Al-Mufadi, F. A., and Almasri, R. A. (May 20, 2019). "Experimental Heat Transfer From Heating Source Subjected to Rigorous Natural Convection Inside Enclosure and Cooled by Forced Nanofluid Flow." ASME. J. Heat Transfer. July 2019; 141(7): 072501. https://doi.org/10.1115/1.4043673
Download citation file:
Get Email Alerts
Cited By
Related Articles
Effects of Variable Viscosity and Thermal Conductivity of CuO-Water Nanofluid on Heat Transfer Enhancement in Natural Convection: Mathematical Model and Simulation
J. Heat Transfer (May,2010)
Nonhomogeneous Model for the Mixed Convection and Entropy Generation of a Nanofluid in a Lid-Driven Inclined Enclosure With Discrete Heat Source
J. Heat Transfer (January,2020)
Optimization of Free Convection Heat Transfer From Vertical Plates Using Nanofluids
J. Heat Transfer (April,2012)
Related Proceedings Papers
Related Chapters
Heat Transfer Characteristics of CNT-Heat Transfer Oil Nanofluid Flow Inside Helically Coiled Tubes under Uniform Wall Tempoerature Condition
International Conference on Computer and Electrical Engineering 4th (ICCEE 2011)
Finite Element Solution of Natural Convection Flow of a Nanofluid along a Vertical Flat Plate with Streamwise Sinusoidal Surface Temperature
International Conference on Computer and Electrical Engineering 4th (ICCEE 2011)
An Approach for Optimizing Thermal Conductivity in Nanofluids
Inaugural US-EU-China Thermophysics Conference-Renewable Energy 2009 (UECTC 2009 Proceedings)