Heat transfer and flow characteristics of Taylor flows in vertical capillaries with tube diameters ranging from 0.5 mm to 2 mm were studied numerically with the volume of fluid (VOF) method. Streamlines, bubble shapes, pressure drops, and heat transfer characteristics of the fully developed gas–liquid Taylor flow were investigated in detail. The numerical data fitted well with experimental results and with the predicted values of empirical correlations. The results indicate that the dimensionless liquid film thickness and bubble rising velocity increase with increasing capillary number. Pressure drops in liquid slug region are higher than the single-phase flow because of the Laplace pressure drop. The flow pattern dependent model and modified flow separation model which takes Bond number and Reynolds number into account can predict the numerical pressure drops well. Compared with the single-phase flow, less time is needed for the Taylor flow to reach a thermal fully developed status. The Nusselt number of Taylor flow is about 1.16–3.5 times of the fully developed single-phase flow with a constant wall heat flux. The recirculation regions in the liquid and gas slugs can enhance the heat transfer coefficient and accelerate the development of the thermal boundary layer.
Issue Section:
Heat and Mass Transfer
References
1.
Triplett
, K.
, Ghiaasiaan
, S.
, Abdel-Khalik
, S.
, and Sadowski
, D.
, 1999
, “Gas–Liquid Two-Phase Flow in Microchannels—Part I: Two-Phase Flow Patterns
,” Int. J. Multiphase Flow
, 25
(3
), pp. 377
–394
.2.
Zhao
, T. S.
, and Bi
, Q. C.
, 2001
, “Co-Current Air–Water Two-Phase Flow Patterns in Vertical Triangular Microchannels
,” Int. J. Multiphase Flow
, 27
(5
), pp. 765
–782
.3.
Liu
, H.
, Vandu
, C. O.
, and Krishna
, R.
, 2005
, “Hydrodynamics of Taylor Flow in Vertical Capillaries: Flow Regimes, Bubble Rise Velocity, Liquid Slug Length, and Pressure Drop
,” Ind. Eng. Chem. Res.
, 44
(14
), pp. 4884
–4897
.4.
Kreutzer
, M. T.
, Kapteijn
, F.
, Moulijn
, J. A.
, Kleijn
, C. R.
, and Heiszwolf
, J. J.
, 2005
, “Inertial and Interfacial Effects on Pressure Drop of Taylor Flow in Capillaries
,” AlChE J.
, 51
(9
), pp. 2428
–2440
.5.
Walsh
, E.
, Muzychka
, Y.
, Walsh
, P.
, Egan
, V.
, and Punch
, J.
, 2009
, “Pressure Drop in Two Phase Slug/Bubble Flows in Mini Scale Capillaries
,” Int. J. Multiphase Flow
, 35
(10
), pp. 879
–884
.6.
Warnier
, M. J. F.
, de Croon
, M.
, Rebrov
, E. V.
, and Schouten
, J. C.
, 2010
, “Pressure Drop of Gas-Liquid Taylor Flow in Round Micro-Capillaries for Low to Intermediate Reynolds Numbers
,” Microfluid. Nanofluid.
, 8
(1
), pp. 33
–45
.7.
Walsh
, P. A.
, Walsh
, E. J.
, and Muzychka
, Y. S.
, 2010
, “Heat Transfer Model for Gas–Liquid Slug Flows Under Constant Flux
,” Int. J. Heat Mass Transfer
, 53
(15–16
), pp. 3193
–3201
.8.
Lim
, Y. S.
, Yu
, S. C. M.
, and Nguyen
, N. T.
, 2013
, “Flow Visualization and Heat Transfer Characteristics of Gas–Liquid Two-Phase Flow in Microtube Under Constant Heat Flux at Wall
,” Int. J. Heat Mass Transfer
, 56
(1–2
), pp. 350
–359
.9.
Leung
, S. S.
, Gupta
, R.
, Fletcher
, D. F.
, and Haynes
, B. S.
, 2011
, “Effect of Flow Characteristics on Taylor Flow Heat Transfer
,” Ind. Eng. Chem. Res.
, 51
(4
), pp. 2010
–2020
.10.
Leung
, S. S. Y.
, Liu
, Y.
, Fletcher
, D. F.
, and Haynes
, B. S.
, 2010
, “Heat Transfer in Well-Characterised Taylor Flow
,” Chem. Eng. Sci.
, 65
(24
), pp. 6379
–6388
.11.
Talimi
, V.
, Muzychka
, Y. S.
, and Kocabiyik
, S.
, 2012
, “A Review on Numerical Studies of Slug Flow Hydrodynamics and Heat Transfer in Microtubes and Microchannels
,” Int. J. Multiphase Flow
, 39
, pp. 88
–104
.12.
Bandara
, T.
, Nguyen
, N. T.
, and Rosengarten
, G.
, 2015
, “Slug Flow Heat Transfer Without Phase Change in Microchannels: A Review
,” Chem. Eng. Sci.
, 126
, pp. 283
–295
.13.
Santos
, R. M.
, and Kawaji
, M.
, 2010
, “Numerical Modeling and Experimental Investigation of Gas-Liquid Slug Formation in a Microchannel T-Junction
,” Int. J. Multiphase Flow
, 36
(4
), pp. 314
–323
.14.
Gupta
, R.
, Fletcher
, D. F.
, and Haynes
, B. S.
, 2010
, “CFD Modelling of Flow and Heat Transfer in the Taylor Flow Regime
,” Chem. Eng. Sci.
, 65
(6
), pp. 2094
–2107
.15.
Qian
, D.
, and Lawal
, A.
, 2006
, “Numerical Study on Gas and Liquid Slugs for Taylor Flow in a T-Junction Microchannel
,” Chem. Eng. Sci.
, 61
(23
), pp. 7609
–7625
.16.
Shao
, N.
, Salman
, W.
, Gavriilidis
, A.
, and Angeli
, P.
, 2008
, “CFD Simulations of the Effect of Inlet Conditions on Taylor Flow Formation
,” Int. J. Heat Fluid Flow
, 29
(6
), pp. 1603
–1611
.17.
Fletcher
, D. F.
, and Haynes
, B. S.
, 2017
, “CFD Simulation of Taylor Flow: Should the Liquid Film Be Captured or Not?
,” Chem. Eng. Sci.
, 167
, pp. 334
–335
.18.
Araújo
, J. D. P.
, Miranda
, J. M.
, Pinto
, A. M. F. R.
, and Campos
, J. B. L. M.
, 2012
, “Wide-Ranging Survey on the Laminar Flow of Individual Taylor Bubbles Rising Through Stagnant Newtonian Liquids
,” Int. J. Multiphase Flow
, 43
, pp. 131
–148
.19.
Asadolahi
, A. N.
, Gupta
, R.
, Leung
, S. S. Y.
, Fletcher
, D. F.
, and Haynes
, B. S.
, 2012
, “Validation of a CFD Model of Taylor Flow Hydrodynamics and Heat Transfer
,” Chem. Eng. Sci.
, 69
(1
), pp. 541
–552
.20.
Asadolahi
, A. N.
, Gupta
, R.
, Fletcher
, D. F.
, and Haynes
, B. S.
, 2011
, “CFD Approaches for the Simulation of Hydrodynamics and Heat Transfer in Taylor Flow
,” Chem. Eng. Sci.
, 66
(22
), pp. 5575
–5584
.21.
Gupta
, R.
, Leung
, S. S. Y.
, Manica
, R.
, Fletcher
, D. F.
, and Haynes
, B. S.
, 2013
, “Hydrodynamics of Liquid–Liquid Taylor Flow in Microchannels
,” Chem. Eng. Sci.
, 92
, pp. 180
–189
.22.
Dai
, Z.
, Guo
, Z.
, Fletcher
, D. F.
, and Haynes
, B. S.
, 2015
, “Taylor Flow Heat Transfer in Microchannels—Unification of Liquid–Liquid and Gas–Liquid Results
,” Chem. Eng. Sci.
, 138
, pp. 140
–152
.23.
Liu
, D.
, and Wang
, S.
, 2008
, “Hydrodynamics of Taylor Flow in Noncircular Capillaries
,” Chem. Eng. Process.: Process Intensif.
, 47
(12
), pp. 2098
–2106
.24.
Zhang
, J.
, Fletcher
, D. F.
, and Li
, W.
, 2016
, “Heat Transfer and Pressure Drop Characteristics of Gas–Liquid Taylor Flow in Mini Ducts of Square and Rectangular Cross-Sections
,” Int. J. Heat Mass Transfer
, 103
, pp. 45
–56
.25.
Falconi
, C. J.
, Lehrenfeld
, C.
, Marschall
, H.
, Meyer
, C.
, Abiev
, R.
, Bothe
, D.
, Reusken
, A.
, Schlüter
, M.
, and Wörner
, M.
, 2016
, “Numerical and Experimental Analysis of Local Flow Phenomena in Laminar Taylor Flow in a Square Mini-Channel
,” Phys. Fluids
, 28
(1
), p. 012109
.26.
Che
, Z.
, Wong
, T. N.
, Nguyen
, N. T.
, and Yang
, C.
, 2015
, “Three Dimensional Features of Convective Heat Transfer in Droplet-Based Microchannel Heat Sinks
,” Int. J. Heat Mass Transfer
, 86
, pp. 455
–464
.27.
Taha
, T.
, and Cui
, Z. F.
, 2006
, “CFD Modelling of Slug Flow Inside Square Capillaries
,” Chem. Eng. Sci.
, 61
(2
), pp. 665
–675
.28.
Taha
, T.
, and Cui
, Z.
, 2004
, “Hydrodynamics of Slug Flow Inside Capillaries
,” Chem. Eng. Sci.
, 59
(6
), pp. 1181
–1190
.29.
Han
, Y.
, and Shikazono
, N.
, 2009
, “Measurement of the Liquid Film Thickness in Micro Tube Slug Flow
,” Int. J. Heat Fluid Flow
, 30
(5
), pp. 842
–853
.30.
Aussillous
, P.
, and Quéré
, D.
, 2000
, “Quick Deposition of a Fluid on the Wall of a Tube
,” Phys. Fluids
, 12
(10
), pp. 2367
–2371
.31.
Langewisch
, D. R.
, and Buongiorno
, J.
, 2015
, “Prediction of Film Thickness, Bubble Velocity, and Pressure Drop for Capillary Slug Flow Using a CFD-Generated Database
,” Int. J. Heat Fluid Flow
, 54
, pp. 250
–257
.32.
Hirt
, C. W.
, and Nichols
, B. D.
, 1981
, “Volume of Fluid (VOF) Method for the Dynamics of Free Boundaries
,” J. Comput. Phys.
, 39
(1
), pp. 201
–225
.33.
Jeon
, S.-S.
, Kim
, S.-J.
, and Park
, G.-C.
, 2011
, “Numerical Study of Condensing Bubble in Subcooled Boiling Flow Using Volume of Fluid Model
,” Chem. Eng. Sci.
, 66
(23
), pp. 5899
–5909
.34.
Brackbill
, J.
, Kothe
, D. B.
, and Zemach
, C.
, 1992
, “A Continuum Method for Modeling Surface Tension
,” J. Comput. Phys.
, 100
(2
), pp. 335
–354
.35.
Zhang
, J.
, and Li
, W.
, 2016
, “Investigation of Hydrodynamic and Heat Transfer Characteristics of Gas–Liquid Taylor Flow in Vertical Capillaries
,” Int. Commun. Heat Mass
, 74
, pp. 1
–10
.36.
Laborie
, S.
, Cabassud
, C.
, Durand-Bourlier
, L.
, and Lainé
, J. M.
, 1999
, “Characterisation of Gas–Liquid Two-Phase Flow Inside Capillaries
,” Chem. Eng. Sci.
, 54
(23
), pp. 5723
–5735
.37.
Li
, W.
, and Wu
, Z.
, 2010
, “A General Correlation for Adiabatic Two-Phase Pressure Drop in Micro/Mini-Channels
,” Int. J. Heat Mass Transfer
, 53
(13–14
), pp. 2732
–2739
.38.
Kim
, S.
, and Mudawar
, I.
, 2013
, “Universal Approach to Predicting Two-Phase Frictional Pressure Drop for Mini/Micro-Channel Saturated Flow Boiling
,” Int. J. Heat Mass Transfer
, 58
(1–2
), pp. 718
–734
.39.
Hughmark
, G. A.
, 1965
, “Holdup and Heat Transfer in Horizontal Slug Gas-Liquid Flow
,” Chem. Eng. Sci.
, 20
(12
), pp. 1007
–1010
.40.
Kreutzer
, M. T.
, Du
, P.
, Heiszwolf
, J. J.
, Kapteijn
, F.
, and Moulijn
, J. A.
, 2001
, “Mass Transfer Characteristics of Three-Phase Monolith Reactors
,” Chem. Eng. Sci.
, 56
(21–22
), pp. 6015
–6023
.Copyright © 2018 by ASME
You do not currently have access to this content.
