This paper presents the results of an experimental study of forced convection heat transfer in a narrow rectangular duct fitted with a circular tube and/or a delta-winglet pair. The duct was designed to simulate a single passage in a fin-tube heat exchanger. Heat transfer measurements were obtained using a transient technique in which a heated airflow is suddenly introduced to the test section. High-resolution local fin-surface temperature distributions were obtained at several times after initiation of the transient using an imaging infrared camera. Corresponding local fin-surface heat transfer coefficient distributions were then calculated from a locally applied one-dimensional semi-infinite inverse heat conduction model. Heat transfer results were obtained over an airflow rate ranging from $1.51×10−3$ to $14.0×10−3kg/s.$ These flow rates correspond to a duct-height Reynolds number range of 670–6300 with a duct height of 1.106 cm and a duct width-to-height ratio, $W/H,$ of 11.25. The test cylinder was sized such that the diameter-to-duct height ratio, $D/H$ is 5. Results presented in this paper reveal visual and quantitative details of local fin-surface heat transfer distributions in the vicinity of a circular tube, a delta-winglet pair, and a combination of a circular tube and a delta-winglet pair. Comparisons of local and average heat transfer distributions for the circular tube with and without winglets are provided. Overall mean fin-surface Nusselt-number results indicate a significant level of heat transfer enhancement associated with the deployment of the winglets with the circular cylinder. At the lowest Reynolds numbers (which correspond to the laminar operating conditions of existing geothermal air-cooled condensers), the enhancement level is nearly a factor of 2. At higher Reynolds numbers, the enhancement level is close to 50%.

1.
Jacobi
,
A. M.
, and
Shah
,
R. K.
,
1995
, “
Heat Transfer Surface Enhancement through the Use of Longitudinal Vortices: A Review of Recent Progress
,”
Exp. Therm. Fluid Sci.
,
11
,
295
309
.
2.
Tiggelbeck
,
S.
,
Mitra
,
N. K.
, and
Fiebig
,
M.
,
1993
, “
Experimental Investigations of Heat Transfer Enhancement and Flow Losses in a Channel with Double Rows of Longitudinal Vortex Generators
,”
Int. J. Heat Mass Transfer
,
36
(
9
),
2327
2337
.
3.
Torii, K., Nishino, K., and Nakayama, K., 1994, “Mechanism of Heat Transfer Augmentation by Longitudinal Vortices in a Flat Plate Boundary Layer,” Proc. Tenth Int. Heat Transfer Conf., Hemisphere, New York, Vol. 6, pp. 123–128.
4.
Fiebig
,
M.
,
Valencia
,
A.
, and
Mitra
,
N. K.
,
1993
, “
Wing-Type Vortex Generators for Fin-and-Tube Heat Exchangers
,”
Exp. Therm. Fluid Sci.
,
7
,
287
296
.
5.
Chen
,
Y.
,
Fiebig
,
M.
, and
Mitra
,
N. K.
,
1998
, “
Conjugate Heat Transfer of a Finned Oval Tube Part B: Heat Transfer Behaviors
,”
Numer. Heat Transfer, Part A
,
33
,
387
401
.
6.
Chen
,
Y.
,
Fiebig
,
M.
, and
Mitra
,
N. K.
,
1998
, “
Heat Transfer Enhancement of a Finned Oval Tube with Punched Longitudinal Vortex Generators In-line
,”
Int. J. Heat Mass Transfer
,
41
,
4151
4166
.
7.
O’Brien, J. E., and Sohal, M. S., 2000, “Local Heat Transfer for Finned-Tube Heat Exchangers using Oval Tubes,” Proceedings, 2000 ASME National Heat Transfer Conference, Pittsburgh, August, Paper no. NHTC2000-12093.
8.
9.
Incropera, F. P., and DeWitt, D. P., 1990, Fundamentals of Heat and Mass Transfer, 3rd ed., J. Wiley, New York.
10.
Moffatt
,
R. J.
,
1982
, “
Contributions to the Theory of Single-Sample Uncertainty Analysis
,”
ASME J. Fluids Eng.
,
104
,
250
260
.