The traditional balancing methods using trial or calibration weights are quite effective, yet too many trials may result in a lengthy balancing process. It had been suggested in the literature that it is possible to balance flexible rotors without the use of trial weights, if a rotor model is available. A procedure is developed in this paper to balance flexible rotors using complex modes and complex vibration measurements. It is shown that a complex rotor model is essential for the success of the technique. Moreover, careful calibration of the rotor model is the major cornerstone of the procedure. Experimental results illustrate the success of the procedure.

Issue Section:
Gas Turbines: Structures and Dynamics
Keywords:
rotors, modal analysis, parameter estimation, calibration, vibration measurement
Topics:
Rotors, Vibration, Vibration measurement
1.
Thearle
,
E. L.
,
1934
, “
Dynamic Balancing of Rotating Machinery in the Field
,”
Trans. ASME
,
56
, pp.
745
–
753
.
2.
Goodman
,
T. P.
,
1964
, “
A Least-Squares Method for Computing Balance Corrections
,”
J. Eng. Ind.
,
86
(
3
), pp.
273
–
279
.
3.
Bishop
,
R. E. D.
, and
Parkinson
,
A. G.
,
1963
, “
On the Isolation of Modes in the Balancing of Flexible Shafts
,”
Proc. Inst. Mech. Eng.
,
177
, pp.
407
–
423
.
4.
El-Shafei
,
A.
,
2001
, “
Static-Couple Balancing of Overhung Rotors
,”
Vibrations
,
17
(
1
), pp.
6
–
11
.
5.
Hundal
,
M. S.
, and
Harker
,
R. J.
,
1966
, “
Balancing of Flexible Rotors Having Arbitrary Mass and Stiffness Distributions
,”
J. Eng. Ind.
,
88
, pp.
217
–
233
.
6.
Palazzolo, A. B., and Gunter, E. J., 1977, “Modal Balancing Without Trial Weights by a Modified Nyquist Plot Procedure,” Vibration Institute, Machinery Vibration Seminar, Cherry Hill, NJ, Nov.
7.
Gash
,
R.
, and
Drechsler
,
J.
,
1978
, “
Modales Auswuchter Elastischer Laufer Ohne Testgewichtssetzungen
,”
Colloid Sci.
, (
320
), pp.
45
–
54
.
8.
Morton
,
P. G.
,
1985
, “
Modal Balancing of Flexible Shafts Without Trial Weights
,”
Proc. Inst. Mech. Eng.
,
199
(
C1
), pp.
71
–
78
.
9.
Meacham, W. L., Brawley, G. H., and Molis, S. J., 1986, “Balancing of Large Steam Turbine-Generator Using MoBal,” EPRI Rotating Machinery Dynamics, Bearings and Seals Symposium, St. Louis, MO, Sept. 9–11.
10.
Wiese, D., 1992, “Two New Procedures to Balance Flexible Rotors Without Test Runs,” Proceedings of the 5th International Conference on Vibrations in Rotating Machinery, Bath, England, IMechE, London, pp. 557–568.
11.
Preciado, E., and Bannister, R. H., 2000, “On the Balancing of Flexible Rotors Without Trial Runs,” Proceedings of the 7th International Conference on Vibrations in Rotating Machinery, Nottingham, England, IMechE, London, pp. 121–130.
12.
RIMAP User Guide, 2000, Version 1.2, RITEC, Egypt.
13.
Ewins, D. J., 1986, Modal Testing: Theory and Practice, Research Studies Press Ltd.
14.
Kreuzinger-Janik, T., and Irretier, H., 2000, “Unbalance Identification of Flexible Rotors Based on Experimental Modal Analysis,” Proceedings of the 7th International Conference on Vibrations in Rotating Machinery, Nottingham, England, IMechE, London, pp. 335–346.
Copyright © 2004
 by ASME
You do not currently have access to this content.