This paper presents an efficient production optimization scheme for an oil reservoir undergoing water injection by optimizing the production rate for each well. In this approach, an adaptive version of simulated annealing (ASA) is used in two steps. The optimization variables updating in the first stage is associated with a coarse grid model. In the second step, the fine grid model is used to provide more details in final solution search. The proposed method is formulated as a constrained optimization problem defining a desired objective function and a set of existing field/facility constraints. The use of polytope in the ASA ensures the best solution in each iteration. The objective function is based on net present value (NPV). The initial oil production rates for each well come from capacity and property of each well. The coarse grid block model is generated based on average horizon permeability. The proposed optimization workflow was implemented for a field sector model. The results showed that the improved rates optimize the total oil production. The optimization of oil production rates and total water injection rate leads to increase in the total oil production from 315.616 MSm3 (our initial guess) to 440.184 MSm3, and the recovery factor is increased to 26.37%; however, the initial rates are much higher than the optimized rates. Beside this, the recovery factor of optimized production schedule with optimized total injection rate is 3.26% larger than the initial production schedule with optimized total water injection rate.
Skip Nav Destination
Article navigation
Research-Article
An Efficient Workflow for Production Allocation During Water Flooding
Vahid Azamipour,
Vahid Azamipour
School of Chemical Engineering,
Iran University of Science and Technology,
Narmak, Tehran 16846-13114, Iran
e-mail: vahid_azami@alumni.ut.ac.ir
Iran University of Science and Technology,
Narmak, Tehran 16846-13114, Iran
e-mail: vahid_azami@alumni.ut.ac.ir
Search for other works by this author on:
Mehdi Assareh,
Mehdi Assareh
School of Chemical Engineering,
Iran University of Science and Technology,
Narmak, Tehran 16846-13114, Iran
e-mail: assarehm@iust.ac.ir
Iran University of Science and Technology,
Narmak, Tehran 16846-13114, Iran
e-mail: assarehm@iust.ac.ir
Search for other works by this author on:
Mohammad Reza Dehghani,
Mohammad Reza Dehghani
School of Chemical Engineering,
Iran University of Science and Technology,
Narmak, Tehran 16846-13114, Iran
e-mail: m_dehghani@iust.ac.ir
Iran University of Science and Technology,
Narmak, Tehran 16846-13114, Iran
e-mail: m_dehghani@iust.ac.ir
Search for other works by this author on:
Georg M. Mittermeir
Georg M. Mittermeir
Search for other works by this author on:
Vahid Azamipour
School of Chemical Engineering,
Iran University of Science and Technology,
Narmak, Tehran 16846-13114, Iran
e-mail: vahid_azami@alumni.ut.ac.ir
Iran University of Science and Technology,
Narmak, Tehran 16846-13114, Iran
e-mail: vahid_azami@alumni.ut.ac.ir
Mehdi Assareh
School of Chemical Engineering,
Iran University of Science and Technology,
Narmak, Tehran 16846-13114, Iran
e-mail: assarehm@iust.ac.ir
Iran University of Science and Technology,
Narmak, Tehran 16846-13114, Iran
e-mail: assarehm@iust.ac.ir
Mohammad Reza Dehghani
School of Chemical Engineering,
Iran University of Science and Technology,
Narmak, Tehran 16846-13114, Iran
e-mail: m_dehghani@iust.ac.ir
Iran University of Science and Technology,
Narmak, Tehran 16846-13114, Iran
e-mail: m_dehghani@iust.ac.ir
Georg M. Mittermeir
1Corresponding author.
Contributed by the Petroleum Division of ASME for publication in the JOURNAL OF ENERGY RESOURCES TECHNOLOGY. Manuscript received April 30, 2016; final manuscript received August 24, 2016; published online October 10, 2016. Assoc. Editor: Egidio Marotta.
J. Energy Resour. Technol. May 2017, 139(3): 032902 (10 pages)
Published Online: October 10, 2016
Article history
Received:
April 30, 2016
Revised:
August 24, 2016
Citation
Azamipour, V., Assareh, M., Dehghani, M. R., and Mittermeir, G. M. (October 10, 2016). "An Efficient Workflow for Production Allocation During Water Flooding." ASME. J. Energy Resour. Technol. May 2017; 139(3): 032902. https://doi.org/10.1115/1.4034808
Download citation file:
Get Email Alerts
Related Articles
Characterization and Prediction of Gas Breakthrough With Cyclic Steam and Gas Stimulation Technique in an Offshore Heavy Oil Reservoir
J. Energy Resour. Technol (May,2017)
A New High-Temperature Gel for Profile Control in Heavy Oil Reservoirs
J. Energy Resour. Technol (March,2016)
A Comparative Study of Genetic and Particle Swarm Optimization Algorithms and Their Hybrid Method in Water Flooding Optimization
J. Energy Resour. Technol (October,2018)
Research for the Enhanced Oil Recovery Mechanism of Heavy Oil after Composite Huff and Puff Assisted by Edge-Bottom Water Displacement
J. Energy Resour. Technol (January,0001)
Related Proceedings Papers
Related Chapters
Combined Cycle Power Plant
Energy and Power Generation Handbook: Established and Emerging Technologies
Corrosion in Injection Systems
Corrosion and Materials in Hydrocarbon Production: A Compendium of Operational and Engineering Aspects
Characterizing the Resource
Geothermal Heat Pump and Heat Engine Systems: Theory and Practice