Reliability of epoxy molding compounds used in plastic packages of integrated circuit (IC) devices depends to a great extent on the level of thermal stresses. These are due primarily to the thermal expansion (contraction) mismatch of the epoxy and the silicon materials. In this analysis we assess the effect of silica fillers on the level of thermal stresses. We conclude that thermal stresses in the compound can indeed be reduced by the application of appropriate fillers. We found that the filler volume concentration does not have to be larger than 30 percent to keep the thermal stresses at a sufficiently low level. This number is close to the filler volume concentration of 30–40 percent in commercially available molding compounds. The obtained results and recommendations can be helpful in the analysis of stresses in, and physical design of, plastic packages.
Skip Nav Destination
Article navigation
September 2001
Technical Papers
Thermoelastic Behavior of Filled Molding Compounds: Composite Mechanics Approach
M. Uschitsky, Member ASME,
M. Uschitsky, Member ASME
Lucent Technologies, Bell Laboratories, Inc., 600 Mountain Ave. Murray Hill, NJ 07974
Search for other works by this author on:
E. Suhir, Fellow ASME,
E. Suhir, Fellow ASME
Lucent Technologies, Bell Laboratories, Inc., 600 Mountain Ave. Murray Hill, NJ 07974
Search for other works by this author on:
G. W. Kammlott
G. W. Kammlott
Lucent Technologies, Bell Laboratories, Inc., 600 Mountain Ave. Murray Hill, NJ 07974
Search for other works by this author on:
M. Uschitsky, Member ASME
Lucent Technologies, Bell Laboratories, Inc., 600 Mountain Ave. Murray Hill, NJ 07974
E. Suhir, Fellow ASME
Lucent Technologies, Bell Laboratories, Inc., 600 Mountain Ave. Murray Hill, NJ 07974
G. W. Kammlott
Lucent Technologies, Bell Laboratories, Inc., 600 Mountain Ave. Murray Hill, NJ 07974
Contributed by the Electrical and Electronic Packaging Division for publication in the JOURNAL OF ELECTRONIC PACKAGING. Manuscript received by the EEPD January 11, 2000.
J. Electron. Packag. Sep 2001, 123(3): 260-267 (8 pages)
Published Online: January 11, 2000
Article history
Received:
January 11, 2000
Citation
Uschitsky, M., Suhir, E., and Kammlott, G. W. (January 11, 2000). "Thermoelastic Behavior of Filled Molding Compounds: Composite Mechanics Approach ." ASME. J. Electron. Packag. September 2001; 123(3): 260–267. https://doi.org/10.1115/1.1349422
Download citation file:
Get Email Alerts
Cited By
Impact of Encapsulated Phase Change Material Additives for Improved Thermal Performance of Silicone Gel Insulation
J. Electron. Packag (December 2024)
Special Issue on InterPACK2023
J. Electron. Packag
Extreme Drop Durability of Sintered Silver Traces Printed With Extrusion and Aerosol Jet Processes
J. Electron. Packag (December 2024)
Related Articles
Thermoelastic Fields of a Functionally Graded Coated Inhomogeneity With Sliding/Perfect Interfaces
J. Appl. Mech (May,2007)
Lead-On-Chip Versus Chip-On-Lead Packages and Solder Failure Criteria
J. Electron. Packag (September,2000)
Linear Thermoelastic Higher-Order Theory for Periodic Multiphase Materials
J. Appl. Mech (September,2001)
Effective Thermomechanical Behavior of Plain-Weave Fabric-Reinforced Composites Using Homogenization Theory
J. Eng. Mater. Technol (January,1994)
Related Proceedings Papers
Related Chapters
Flexibility Analysis
Process Piping: The Complete Guide to ASME B31.3, Third Edition
Theoretical Analysis and Application of Pile Shaft Resistance Strengthening Effect
International Conference on Optimization Design (ICOD 2010)
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design